Air Compressor - Portable - Makita MAC5501G Manual

The Makita MAC5501G is a portable air compressor designed for a variety of applications, including powering pneumatic tools, inflating tires, and more. It features a powerful 5.5 HP motor, a 4.2-gallon tank, and a maximum pressure of 130 PSI. The compressor is lightweight and easy to transport, making it ideal for both professional and DIY use. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operating Instructions 8. Maintenance 9. Safety Information 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 5.5 HP motor, 4.2-gallon tank, maximum pressure of 130 PSI, lightweight design, and easy portability.

FeatureDescription
5.5 HP MotorPowerful motor for efficient performance
4.2-Gallon TankProvides ample air storage for various tasks
130 PSI Maximum PressureSuitable for a wide range of pneumatic tools
Portable DesignLightweight and easy to transport
Oil-Lubricated PumpEnsures durability and longevity
Low Noise LevelOperates quietly for user comfort

Installation

Unpack and inspect contents. Place the compressor on a stable surface.

  1. Connect the air hose: Ensure a secure connection to the compressor outlet.
  2. Check oil level: Ensure the oil is at the recommended level before operation.
  3. Plug into AC power: Use a grounded outlet to avoid electrical hazards.

WARNING! Ensure all connections are secure and check for leaks before use.

First-Time Setup

Power on the compressor; follow the setup instructions.

  1. Check pressure settings: Adjust to the desired PSI for your application.
  2. Test operation: Run the compressor briefly to ensure proper function.
  3. Inspect for leaks: Check all connections for air leaks.

CAUTION! Ensure the compressor is on a flat surface during operation.

Specifications

Controls and Settings

Access controls on the front panel: Pressure gauge, on/off switch, and regulator.

Pressure Gauge: Displays current tank pressure.

Regulator: Adjusts output pressure for connected tools.

Connecting Devices

Connect pneumatic tools using the air hose to the compressor outlet.

  1. Turn off the compressor before connecting tools.
  2. Ensure the hose is securely attached to both the compressor and the tool.
  3. Turn on the compressor and adjust the pressure as needed.

Tip: Always check for leaks after connecting devices.

Operating Instructions

Follow these steps to operate the compressor safely and effectively.

  1. Power on the compressor using the on/off switch.
  2. Adjust the pressure regulator to the desired level.
  3. Connect your pneumatic tool and begin operation.
  4. Monitor the pressure gauge during use.

WARNING! Do not exceed the maximum pressure rating.

Maintenance

Regular maintenance is essential for optimal performance.

  1. Check oil level regularly and change as needed.
  2. Inspect air filters and replace if dirty.
  3. Drain the tank regularly to remove moisture.

CAUTION! Always unplug the compressor before performing maintenance.

Safety Information

Read all safety instructions before operating the compressor.

Regulatory Information

This compressor complies with all applicable safety standards and regulations. For support, visit www.makitatools.com or contact customer service.

Troubleshooting

SymptomPossible CauseCorrective Action
Compressor won't startPower supply issueCheck power cord and outlet.
Low pressureLeak in hoseInspect hose for damage and replace if necessary.
Excessive noiseLoose partsTighten all screws and bolts.
Oil leaksWorn sealsReplace seals as needed.

Reset: Disconnect power and reconnect to reset the compressor.

Service: For service inquiries, contact Makita customer support.

Air Compressor - Portable - Makita MAC5501G Manual © - All Rights Reserved 2026